收藏本站
LT3597
APPLICATIONS INFORMATION
V D + V OUT
V IN ? V CESAT + V D
? ? + V CESAT ? V D
V IN(MIN) = ?
MinimumInputVoltage
The minimum input voltage required to generate an output
voltage is limited by the maximum duty cycle and the
output voltage (V OUT ) set by the FB resistor divider. The
duty cycle is:
DC =
where V D is the Schottky forward drop and V CESAT is the
saturation voltage of the internal switch. The minimum
input voltage is:
? V D + V OUT(MAX) ?
? DC MAX
where V OUT(MAX) is calculated from the equation in the
Adaptive Loop Control section, and DC MAX is the minimum
rating of the maximum duty cycle.
Fault Flag
The FAULT pin is an open-collector output and needs an
external resistor tied to a supply. If the LED1-3 pin volt-
age exceeds 12V or if the LED1-3 pin voltage is within
1.25V of V OUT1-3 pins while PWM1-3 is high, the FAULT
pin will be pulled low. The FAULT pin will also be pulled
low if the internal junction temperature exceeds the T SET
programmed temperature limit.
There is an approximate 3μs delay for FAULT flag generation
when the PWM1-3 signal is enabled to avoid generating
a spurious flag signal. The maximum current the FAULT
can sink is typically 200μA.
Thermal Considerations
The LT3597 provides three channels for LED strings with
internal NPN devices serving as constant current sources.
When LED strings are regulated, the lowest LED pin volt-
age is typically 1V. More power dissipation occurs in the
LT3597 at higher programmed LED currents. For 100mA
of LED current with a 100% PWM dimming ratio, at least
300mW is dissipated within the IC due to current sources.
Thermal calculations must include the power dissipation
in the current sources in addition to conventional switch
DC loss, switch transient loss and input quiescent loss.
In addition, the die temperature of the LT3597 must be
lower than the maximum rating of 125°C. This is generally
not a concern unless the ambient temperature is above
100°C. Care should be taken in the board layout to ensure
good heat sinking of the LT3597. The maximum load
current should be derated as the ambient temperature ap-
proaches 125°C. The die temperature rise above ambient
is calculated by multiplying the LT3597 power dissipation
by the thermal resistance from junction to ambient. Power
dissipation within the LT3597 is estimated by calculating
the total power loss from an efficiency measurement and
subtracting the losses of the catch diode and the inductor.
Thermal resistance depends on the layout of the circuit
board, but 32°C/W is typical for the 5mm × 8mm QFN
package.
Board Layout
As with all switching regulators, careful attention must be
paid to the PCB board layout and component placement.
To prevent electromagnetic interference (EMI) problems,
proper layout of high frequency switching paths is essen-
tial. Minimize the length and area of all traces connected
to the switching node pin (SW). Always use a ground
plane under the switching regulator to minimize inter-
plane coupling. Good grounding is essential in LED fault
detection.
Proper grounding is also essential for the external resistors
and resistor dividers that set critical operation parameters.
Both the LT3597 exposed pad and pin 18 are ground.
Resistors connected between ground and the CTRL1-3,
CTRLM, FB1-3, T SET , I SET1-3 , RT and EN/UVLO pins are
best tied to pin 18 and not the ground plane.
3597fa
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LT3598IUF#PBF IC LED DRIVR WHITE BCKLGT 24-QFN
LT3599IFE#PBF IC LED DRVR WHITE BCKLGT 28TSSOP
LT3743EFE#PBF IC LED DVR HP CONST CURR 28TSSOP
LT3745IUJ#TRPBF IC LED DVR 16CH 50MA 40QFN
LT3746IUHH#TRPBF IC LED DRIVER 32CHANNEL 56-QFN
LT3754IUH#TRPBF IC LED DVR 16CH 50MA 32QFN
LT3755EMSE#PBF IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF IC LED DVR WHT/CLR BCKLT 28TSSOP
相关代理商/技术参数
LT3597EUHG#TRPBF 功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3597IUHG#PBF 功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3597IUHG#TRPBF 功能描述:IC LED DRIVER 60V TRIPLE 52-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3598 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Triple Step-Down LED Driver Programmable Temperature Protection
LT3598_1 制造商:LINER 制造商全称:Linear Technology 功能描述:6-String 30mA LED Driver with 1.5% Current Matching
LT3598EFE#PBF 功能描述:IC LED DRVR WHITE BCKLGT 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3598EFE#PBF 制造商:Linear Technology 功能描述:LED DRIVER BOOST PWM 2.5MHZ 制造商:Linear Technology 功能描述:LED DRIVER, BOOST, PWM, 2.5MHZ, TSSOP-24
LT3598EFE#TRPBF 功能描述:IC LED DRVR WHITE BCKLGT 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND